home *** CD-ROM | disk | FTP | other *** search
-
-
- Please note that the information in this file is written in two languages.
- Refer to Section A for English version and Section B for German version.
-
-
- Section A :
- *********************************************************************
- * Additional Information *
- * *
- * AZT IDE CD-ROM Drive Installation Disk ver 2.22 *
- *********************************************************************
-
- This file contains additional information about the CD-ROM drive
- installation software that was not available at printing time.
-
-
- General Information
- ===================
-
- Standard IDE supports up to a maximum of two IDE interfaces. Each IDE
- interface can support up to a maximum of two devices, i.e. either 2 hard
- disks, 2 CD-ROM drives or a combination of 1 hard disk & 1 CD-ROM drive.
- The port address for Primary & Secondary IDE interface is at 1F0H & 170H
- respectively.
-
- Primary IDE interface refers to the interface (at 1F0H) on your system
- where the IDE hard disk is connected (it can be built-in on the system
- motherboard or on a separate I/O card). Secondary IDE interface (at 170H)
- refers to the IDE interface on a separate interface card (e.g. the
- interface card bundled with this CD-ROM drive, on-board Secondary IDE
- interface or the interface on the sound card).
-
-
- CD-ROM Drive Configuration
- ==========================
-
- Please note that the IDE CD-ROM drive is factory configured to Single/Slave
- drive setting. Therefore, the following points are to be observed during
- the installation of the CD-ROM drive :
-
- 1.) If you are connecting the CD-ROM drive directly to the provided
- interface card or your system's on-board Secondary IDE interface,
- no jumper setting is required on either the CD-ROM or hard disk drive.
- If the on-board Secondary IDE interface has a hard disk connected,
- ensure that it is configured to Master drive setting. Please refer
- to your hard disk reference manual for more information.
-
- 2.) If your Sound Card has an IDE interface, please install the CD-ROM
- drive through the interface on the sound card. Please ensure that the
- jumper setting on the sound card is properly configured to IDE CD-ROM
- interface. For more information, refer to your sound card user's
- manual.
-
- 3.) If you are connecting the CD-ROM drive and the hard disk together
- through the on-board Primary IDE interface,
-
- a.) Please ensure that your hard disk is configured to Master drive
- setting. For more information, please refer to your hard disk
- reference manual.
-
- b.) Please also make sure that the following statement is in the
- [386Enh] section in the SYSTEM.INI file under WINDOWS directory.
-
- [386Enh]
- 32bitdiskaccess=OFF
-
- 4.) If you are connecting two CD-ROM drives directly to the provided
- interface card or your system's on-board Secondary IDE interface,
- ensure that one CD-ROM drive is configured to Master drive and the
- other to Slave drive setting. Please refer to the CD-ROM drive manual
- for more information on how to configure the drives.
-
-
-
- Section B :
- *************************************************************************
- * Zusätzliche Informationen *
- * *
- * AZT IDE CD-ROM Laufwerk Ver 2.10 *
- *************************************************************************
-
- In dieser Datei finden Sie zusätzliche Informationen zur CD-ROM Laufwerk
- Installationssoftware, die bei Drucklegung nicht verfügbar war.
-
-
- Allgemeine Informationen
- ========================
-
- Standard IDE unterstützt maximal zwei IDE Schnittstellen. An jeder IDE
- Schnittstelle können maximal zwei Geräte angeschlossen sein, z.B. zwei
- Festplattem zwei CD-ROM Laufwerke oder eine Kombination aus einer
- Festplatte und einem CD-ROM Laufwerk. Die Portadresse für ein primäres IDE
- Interface ist 1F0H und für ein sekundäres IDE Interface 170H.
-
- Das primäre IDE Interface ist der Anschluß (bei Adresse 1F0H), an dem Ihre
- Festplatte(n) angeschlossen ist. Es kann auf dem Mainboard oder auf einer
- Controllerkarte eingebaut sein. Ein sekundäres IDE Interface (bei Adresse
- 170H) ist dann in Ihrem System vorhanden, wenn Sie in Ihrem System vier
- AT-Bus Festplatten installieren können. Sie finden es dann ebenfalls auf
- dem Mainboard oder auf der Controllerkarte. Ein zusätzliches sekundäres IDE
- Interface kann auch das auf bestimmten Soundkarten (z.B. Aztech WaveRider
- 32+) eingebaute sekundäre IDE Interface oder das auf der optionalen
- Schnittstellenkarte zum IDE CD-ROM Laufwerk enthaltene Interface sein.
-
-
- CD-ROM Laufwerk Konfiguration
- =============================
-
- Beachten Sie bitte, daß das IDE CD-ROM Laufwerk ab Werk als Single/Slave
- Laufwerk konfiguriert ist. Bei der Installation dieses Laufwerks müssen
- folgende Punkte beachtet werden:
-
- 1.) Wenn Sie das CD-ROM Laufwerk direkt an der optionalen Interfacekarte
- von Aztech oder an einem anderen sekundären Interface in Ihrem PC
- anschließen, so brauchen keine Jumper verändert zu werden. Wenn am
- sekundären IDE Interface in Ihrem System bereits eine Festplatte
- installiert ist, muß diese als Master konfiguriert sein. Die korrekte
- Jumpereinstellung entnehmen Sie bitte der Anleitung Ihrer Festplatte.
-
- 2.) Wenn an Ihrer Soundkarte ein IDE Interface vorhanden ist, schließen
- Sie das CD-ROM Laufwerk bitte dort an. Stellen Sie sicher, daß mit
- dem Jumper auf der Soundkarte die IDE Schnittstelle eingeschaltet
- ist. Weitere Hinweise finden Sie im Soundkartenhandbuch.
-
- 3.) Wenn Sie das CD-ROM Laufwerk zusammen mit einer Festplatte an einem
- primären IDE Interface in Ihrem System anschließen wollen, dann
- beachten Sie folgende zwei Punkte:
-
- a) Stellen Sie sicher, daß die (einzige) Festplatte als Master
- konfiguriert ist. Die korrekte Jumpereinstellung entnehmen
- Sie bitte der Anleitung Ihrer Festplatte.
-
- b) Stellen Sie auch sicher, daß die folgende Zeile im Abschnitt
- [386Enh] der SYSTEM.INI Datei im WINDOWS Verzeichnis steht:
-
- [386Enh]
- 32BitDiskAccess=OFF
-
- 4.) Wenn Sie zwei IDE CD-ROM Laufwerke an einem vorhandenen sekundären
- IDE Interface in Ihrem System anschließen wollen, so muß das eine
- CD-ROM Laufwerk als Master umkonfiguriert werden, während das andere
- weiter als Slave konfiguriert bleibt. Informationen zu diesem Thema
- finden Sie in Ihrem CD-ROM Handbuch.
-
- In diesem Fall kopieren Sie die Zeile DEVICE=(Pfad)SGIDECD.SYS...
- in der Datei CONFIG.SYS und editieren die zweite Zeile, so daß die
- Namen der Laufwerke unterschiedlich sind. Die Zeilen können dann
- z.B. so aussehen:
-
- (Config.sys)
- DEVICE=C:\WR32\DRIVERS\SGIDECD.SYS /D:MSCD001
- DEVICE=C:\WR32\DRIVERS\SGIDECD.SYS /D:MSCD002
-
- Editieren Sie dann die Zeile mit dem Aufruf von MSCDEX.EXE in der
- Startdatei AUTOEXEC.BAT folgendermaßen:
-
- (Autoexec.bat)
- C:\DOS\MSCDEX.EXE /D:MSCD001 /D:MSCD002
-
- Hier reicht also eine Zeile, in der beide Namen genannt werden. Der
- Pfad C:\DOS ist hier nur ein Beispiel und kann in Ihrer Autoexec.bat
- Datei anders lauten. Auch können weitere Parameter folgen. Lassen Sie
- diese, wie sie sind, fügen Sie lediglich /D:MSCD002 zusätzlich ein.
-
-
- --- Ende der Datei ---
-